Shopping: Real Estate |  Costumes  |  Guitars
This Issue Archived Articles Blog About Us Contact Us
SEARCH


Building an Ultra Light-Weight Car, Part 2

Forming a curved body without moulds or panel beating

by Julian Edgar

Click on pics to view larger images

At a glance...

  • Using shaped foam to form the external body contours
  • All done with hand tools!
  • The University of South Australia’s ultra light-weight electric car
Email a friend     Print article
This article was first published in 2009.

Last week in Building an Ultra Light-Weight Car, Part 1 we looked at how the University of South Australia has built the monocoque tub of an ultra lightweight and innovative, three-wheel electric car. Rather than using a steel or aluminium tubular space-frame structure, the strength of the vehicle lies in a monocoque constructed from foldable, aluminium honeycomb/fibreglass sandwich panels.

Click for larger image

That approach resulted in a complete tub that weighs just 32kg yet has room to carry two people. But yes you’re right, it doesn’t look very aerodynamic, does it... So in this story we look at how the monocoque was clothed in aerodynamic bodywork, a process that before paint, added just 13kg!

Making the Bodywork

The bodywork was formed by a deceptively simple approach, one that could be achieved by anyone working in their home workshop. It takes patience and care, but as University of South Australia’s Dr Peter Pudney said: “None of us had shaped a polystyrene body before!”

Click for larger image

Adfoam ‘M’ grade modelling type expanded polystyrene blocks were cut and then epoxy’d to the fibreglass/aluminium sandwich panels. (Go to www.adfoam.com.au for more details on this foam.) While the epoxy was curing, the foam was held in place with an elastic trailer cargo net and various props.

Click for larger image

The thickness of the foam was tailored to the final shape, with relatively small thicknesses used where the composite panels were close to the required shape...

Click for larger image

... and greater thicknesses used where extensive curvature was needed. The individual foam blocks were shaped so that clearances between adjoining foam blocks were minimal.

Click for larger image

The foam was then simply hand-carved to shape! Surform files, sandpaper, sanding blocks, surface levellers, hot wire cutters and other tools were used, aided by MDF templates and a marked-out grid on the work surface. This shows the body within 20mm of the final shape...

Click for larger image

...and then nearly finished.

Click for larger image

Low spots were filled with polyurethane expanding foam, before being reshaped. Peter Pudney points out that this is not a good approach to take: better to cut out the low spots and fill the area with a new block of the original foam. (This would have avoided sanding across foams with different hardness characteristics.)

Click for larger image

The foam was then covered in a layer of fibreglass cloth and epoxy resin...

Click for larger image

...and then a second layer of fibreglass and resin was applied, the latter complete with red pigment. Sanding then followed. The red pigment acted as an indicating coat, showing the depth to which the sanding had penetrated.

Click for larger image

A carbon fibre reinforcement hoop was installed on the upper surface of body; the acrylic canopy (to be covered in a moment) rests on this. The canopy edge was reinforced with carbon fibre tape laid over plastic polypipe.

Click for larger image

The openings for the rear lights and the rear suspension and wheel were cut out, followed by...

Click for larger image

... the openings for the front lights, the latter being done with a jigsaw. These exposed foam areas were then fibreglassed.

Click for larger image

The body then went to a professional spray shop where the body was further smoothed using body filler and then painted. The additional mass of the foam and fibreglass body was 13kg; painted and smoothed, this increased by another 9kg.

Canopy

Click for larger image

The plastic canopy was made from 3mm clear acrylic. It was free-blown but a template was developed that delineated the shape of the plastic blank; this was mathematically modelled so that the free-blown shape would result in a bubble from which the correctly shaped canopy could be cut.

Click for larger image

The canopy was blown by Ian Linke of Aviation Acrylic Mouldings, a specialist in blowing canopies for gliders. The canopy weighs 10kg.

Click for larger image

Final trimming of the canopy was made on the body of the car. The canopy is hinged at the rear but plans are afoot for a change to side hinging.

Conclusion

Click for larger image

The most fascinating aspect about the construction of the University of South Australia’s car is that with the exception of the canopy blowing and final painting, the constructional techniques can all be done by amateurs working with just hand tools. There’s no need for welding gear, building moulds or panel beating. There’s not even a requirement for a large workspace.

The exterior body techniques lend themselves to custom, compound curve shapes, and the monocoque chassis can be as heavy duty (or as light duty) as the requirements demand.

For example, the 64kg total mass of the body and canopy could be halved if the vehicle was to carry only one person and be powered by a tiny electric or internal combustion engine. On the other hand, we can see a stiff and gusseted monocoque body of a small, open four wheel car coming in at only 150kg or so...

Contacts

Ayres Lightweight Panel Systems www.ayrescom.com

Adform www.adfoam.com.au

UniSA Two-seater Renewable Energy Vehicle. http://www.unisa.edu.au/solarcar/trev/


And the Car as a Whole?

As we’ve indicated, the most impressive feature of the University of South Australia’s car (they call it ‘Trev’) is its body design and construction. But what about the rest of the car?

Click for larger image

In short, it’s largely a build in progress. The car is currently powered by a 6000 rpm, brushed DC electric motor driving the rear wheel through a two-stage drive belt reduction. The motor is powered by a 45kg lithium ion battery pack, giving a range of 120 kilometres. A commercial power controller is used.

Click for larger image

In this form, the car has completed the Darwin to Adelaide World Solar Challenge, running in the Greenfleet Technology Class.

Click for larger image

We were able to drive the car around the roads of the Mawson Lakes campus. Unfortunately (or fortunately?) for our drive, the car could not be equipped with its canopy.

The car shows enormous promise. The steering is light and direct and the performance excellent. (The claim is for a top speed of 120 km/h and 0-100 km/h in around 10 seconds, but with the instant electric motor torque, it feels faster-accelerating than that.) But the low-speed throttle control is dreadful, completely destroying the refined feel that would otherwise be associated with the electric motor.

Click for larger image

The ride quality from the front wishbones and rear trailing arm (sprung and damped with motorcycle units) is fine on smooth surfaces but on rough surfaces, the suspension shows severely inadequate travel. Corner hard and then pass over a bump and the result is simply awful. The brakes are so bad it’s easy to assume they’re not connected.

Click for larger image

The interior of the car is more of that ‘work in progress’ without a proper dashboard or interior trimming. To our way of thinking, the current dashboard LCD is over-kill – although the intention is to add a rear-view camera, which would give a better reason for its presence. Other on-board electronics are overly complex - including a whole computer system to control just the lights!

Click for larger image

But what works well, works very well.

Considering the overall dimensions, interior space is excellent. The rear-hinged, wide door and the heavily cutaway floor combine in a design master-stroke – an adult can easily get into the back seat (or where the back seat would go if the car currently had a back seat!) and access to the driver’s seat is straightforward. There’s a huge amount of room in the doors and the dash panel is spacious, although the storage space in front of the dash is inaccessible. Luggage room is just a little tight – not much is needed in a car of this type but it could probably be better optimised. Incidentally, program director Peter Pudney is well aware of these deficiencies.

Click for larger image

But instead of thinking of what the car is like now, think of what a car could be like! Start by fitting decent, long-travel suspension (perhaps air springs would be best) and a stiff anti-roll bar (remember, the back wheel provides zero roll stiffness!).

Add a decent motor speed controller driving a three-phase brushless motor with regen braking, and you’re starting to talk about a car that would be economical (it currently costs 1.1 cents per kilometre in electricity power cost), practical for city use, and simply a helluva lot of fun to drive...

A real car of the future.

Did you enjoy this article?

Please consider supporting AutoSpeed with a small contribution. More Info...


Share this Article: 

More of our most popular articles.
Fuel economy of 1 litre/100km from an amazing car

Technical Features - 11 June, 2002

The World's Most Fuel-Efficient Car

If you do any work with your hands, you need one of these.

DIY Tech Features - 28 July, 2008

Bench Vices

A new low cost data logger

DIY Tech Features - 30 June, 2009

Five Channel USB Data Logger, Part 1

To improve fuel economy, why not just reduce the amount of fuel that's injected?

Technical Features - 5 August, 2008

Running Lean for Economy

Building a speaker system into the floor and walls of a house

DIY Tech Features - 13 November, 2012

Sound in the Lounge, Part 1

Installing lights in a home workshop

DIY Tech Features - 16 September, 2008

Building a Home Workshop, Part 6

Building a heavy duty mount

DIY Tech Features - 24 July, 2012

Relocating the alternator

Quick, easy and effective

DIY Tech Features - 11 January, 2011

Fitting a Short-Shift

The concrete

DIY Tech Features - 21 February, 2012

A New Home Workshop, Part 4

An auto trans cooler that will cost you almost nothing

Technical Features - 12 February, 2008

Cooling the Trans

Copyright © 1996-2020 Web Publications Pty Limited. All Rights ReservedRSS|Privacy policy|Advertise
Consulting Services: Magento Experts|Technologies : Magento Extensions|ReadytoShip